10106-05-30-10-02-00 - Eddy Current Vibration Probe - 5mV/mm/s IP67 SS 10M Industrial Sensor

1. Triaxial Hazardous-Area Vibration Sensor Overview​

The ProvibTech 10106-05-30-10-02-00 is an intrinsically safe triaxial accelerometer engineered for explosive industrial environments. Featuring ​​±5g measurement range per axis (05 suffix)​​ with ​30mV/g sensitivity (30 designation)​, this sensor captures simultaneous X/Y/Z vibrations with ​​<2% cross-axis error. Its ​hermetically sealed titanium housing (Ti-6Al-4V)​​ provides ​IP68/IP69K protection​ against corrosive chemicals and 100-bar washdowns. The ​10-meter mineral-insulated cable (10)​​ ensures EMI immunity, while the ​M12-5pin connector with TEDS (02-00)​​ enables plug-and-play calibration. Certified for ​ATEX/IECEx Zone 21​ and operating from ​​-40°C to +125°C, it delivers precision vibration data for turbines, compressors, and presses in oil/gas, mining, and chemical processing where explosive dust/gas atmospheres demand maximum safety.

​2. Critical Performance Specifications​

This triaxial sensor achieves ±1% FS accuracy across a 0.5Hz–8kHz frequency range with 30mV/g sensitivity per axis. Electrical specifications include IEPE constant current excitation (2-10mA @ 18-30V DC), <100Ω output impedance, and IEEE 1451.4 TEDS memory. The titanium housing withstands pH 1-14 chemicals with 1,500hr salt spray resistance (ISO 9227). Environmental resilience includes IP68 (3m/24hr submersion), IP69K (100 bar @ 85°C), and 10,000g shock survival. Cross-axis sensitivity is maintained below 2% with ±0.5° phase coherence. Certifications cover ATEX II 2G Ex ia IIC T125°C Ga and IECEx equivalents for Zone 21 hazardous areas.

​3. Explosive Environment Applications​

Designed for critical monitoring in combustible atmospheres:

• ​Offshore Gas Compressors: Casing vibration in Zone 21 gas groups
• ​Coal Processing Plants: Crusher bearing monitoring in explosive dust
• ​Refinery Turbines: Blade-pass frequency analysis with ATEX compliance
• ​Grain Silo Conveyors: Bearing defect detection in combustible dust
• ​Chemical Reactors: Agitator shaft monitoring with acid vapor resistance
• ​Paint Spray Booths: Fan imbalance detection with solvent resistance
• ​Mining Drilling Rigs: Gearbox health in methane-rich atmospheres
• ​Aircraft Fuel Systems: Pump vibration in flammable vapor zones
  The Zone 21 certification ensures safe operation where explosive concentrations exist during normal operation, while titanium construction resists hydrogen sulfide corrosion in sour gas applications.

​4. Functional Advantages​

• ​Multi-Axis Efficiency:
  Single-point installation captures 3D vibration vectors
  Phase-synchronized sampling (±0.5°) for ODS analysis
• ​Hazardous Area Safety:
  Intrinsic safety barriers (Ui=5V, Ii=10mA)
  Hermetic seals prevent gas ingress in explosive atmospheres
• ​Signal Integrity:
  Mineral-insulated cable provides >100dB EMI rejection
  Low-noise electronics (80μg/√Hz) enable sub-Hz detection
• ​Corrosion Defense:
  Titanium housing withstands seawater/pH extremes
  Hydrolysis-resistant cable jacket (ISO 1817)
• ​Maintenance Optimization:
  TEDS auto-configuration reduces calibration errors
  Hot-swappable M12 connectors enable <5-min replacement
• ​Diagnostic Precision:
  NIST-traceable calibration per ISO 16063-21
  Continuous bias current monitoring (4mA ±0.5mA)

​5. Triaxial Sensing Operation​

​Measurement Sequence:

1. ​Quartz Crystal Sensing:
   • Orthogonal shear-mode crystals generate axis-specific charge
2. ​IEPE Signal Conditioning:
   • Low-noise amplifiers per channel (0.5Hz high-pass filtering)
   • Automatic temperature compensation (±0.05%/°C)
3. ​Output Configuration:
   • X/Y/Z signals via M12 pins 1/2/3
   • TEDS data on pin 5 (IEEE 1451.4)
   • Constant current input on pin 4

​Safety & Diagnostics:

• ​Fault Responses:
  Output clamps to 0V during sensor fault
  Current drop <1.5mA indicates cable break
  TEDS Error Code 1 flags internal failure
• ​Explosion Protection:
  Energy-limited design prevents ignition
  <0.015W power dissipation in fault conditions
• ​Overload Protection:
  ±5V output clipping at >5.5g acceleration
  Automatic recovery after overload clearance

Packaging & Shipping

Company Information
Xiamen ZhiCheng Automation Technology Co., Ltdit is a leading global supplier of control system components. We specialize in control systems and drives.

With many years of experience in the industrial sector, we consistently deliver the highest quality of spare parts.which make sure that all this jobs are

perfectly.

we are major in PLC,Sensors,HIM,Transmitters.

Best Supply Brands As Following:1)Bently nevada.2)+GF+.3)Rosemount.4)ABB.5)Allen-Bradley.6)Foxobro.Good working environment, perfect team, sincere cooperation →→ Achieve u and our success !!!